Men's Wheels logo Men's WheelsCars, bikes and the road
Motorcycles

How to Wash a Motorcycle Without Damaging the Bike

A dirty bike looks bad, but a badly washed bike can end up worse. Pressure washers push water into wheel bearings and switchgear, the wrong cleaner dulls the paint, and a wet chain left overnight starts to rust by morning.

A rider rinsing soap off a sport motorcycle on a driveway with a garden hose and two buckets nearby

A dirty bike looks bad, but a badly washed bike can end up worse. Pressure washers push water into wheel bearings and switchgear, the wrong cleaner dulls the paint, and a wet chain left overnight starts to rust by morning.

This guide shows you how to wash a motorcycle properly in about 45 minutes, using a hose, two buckets and a few basic products. It covers what to protect before you start, the order to clean in, how to dry the bike, and the step most riders skip: looking after the chain afterwards.

What you need to wash a motorcycle

  • Two buckets, one for soapy water and one for rinsing the mitt
  • A motorcycle-specific or pH-neutral car shampoo
  • A soft wash mitt and a separate old sponge or brush for the wheels and lower parts
  • A soft-bristled detailing brush, around 2.5 cm wide, for tight areas
  • A dedicated motorcycle cleaner spray for heavy road grime, optional
  • A garden hose with a spray nozzle
  • Two or three large microfibre drying towels
  • Plastic bags and elastic bands, or tape
  • Chain cleaner and chain lube

Wash the bike when the engine and exhaust are cold. Cold water on a hot exhaust can cause staining and, on some bikes, discolouration of the headers. Wait at least an hour after a ride.

Protect the sensitive parts first

Water itself is not the enemy, but water forced into the wrong places is. Before you start, cover or avoid these areas:

  • Exhaust outlet: slip a plastic bag over it and hold it with an elastic band.
  • Air intake: on bikes with exposed intakes, cover them the same way.
  • Ignition and switchgear: do not spray directly at the key barrel or handlebar switches.
  • Dash and electronics: wipe the display by hand rather than hosing it.

Remove anything loose, such as a tank bag, phone mount or soft luggage. If the bike has a USB socket, close its cover.

How to wash a motorcycle step by step

  1. Rinse from the top down. Use a gentle hose setting to soften dirt and wash off loose grit. Grit dragged across paint with a mitt is what causes swirl marks.
  2. Spray cleaner on the dirty areas. If you are using a motorcycle cleaner, spray the lower engine, swingarm and wheels. Leave it for two to three minutes, no longer, and never let it dry on.
  3. Wash the bodywork with the mitt. Dip it into the soapy bucket, wash one panel at a time, starting with the tank and screen, then rinse the mitt in the clean bucket before going back for more soap.
  4. Clean the wheels and lower parts last. Use the separate sponge or brush. The wheels carry brake dust and road grime that will scratch paint if it ends up on the mitt.
  5. Use the detailing brush for spokes, around the brake calipers and between engine fins.
  6. Rinse thoroughly. Again top down, with low pressure, until there is no soap left.

For a commuter bike ridden through winter, you may need a second pass on the lower half. Road salt is what does the real damage, and it gathers under the engine and around the footpegs.

Why I avoid pressure washers on motorcycles

Many riders use a pressure washer because it is fast, and plenty of guides say it is fine if you keep your distance. I disagree, at least for regular washing.

A typical home pressure washer runs at 100 to 140 bar. Even from half a metre, that can force water past the seals in wheel bearings, steering head bearings, swingarm pivots and chain O-rings. You will not notice anything for months, until a bearing starts to feel notchy or the chain develops tight links. The cost of replacing wheel bearings at a garage often runs to 80 to 150 pounds for both wheels. A hose takes ten minutes longer and avoids all of that.

If you must use one, stand at least a metre back, use the widest fan nozzle, and never aim at bearings, seals, electrics or the chain.

Drying the bike properly

Drying is where most riders cut corners, and it is where water spots and rust start.

  1. Take the bags off the exhaust and intake.
  2. Pat the bodywork dry with a microfibre towel. Do not rub hard.
  3. Use a second towel for the frame, engine and wheels.
  4. Start the engine and let it idle for three to five minutes. Engine heat evaporates water from the hard-to-reach areas.
  5. Gently pump the brakes a few times during a short ride so the discs dry and any light surface rust is cleared.

A leaf blower or a cheap electric air blower is an excellent way to clear water from switchgear, the radiator and between spokes, without touching anything.

Do not skip the chain

Washing strips the lube from your chain, and a chain left wet with no lube starts to rust within a day. Once the bike is dry:

  1. Spray chain cleaner on the lower run of the chain while rotating the rear wheel by hand, with the bike on a paddock stand.
  2. Wipe it with a rag until the rag comes away mostly clean.
  3. Apply chain lube to the inside of the chain where it meets the sprockets, one full rotation.
  4. Leave it for 15 to 20 minutes before riding so the lube sets and does not fling off.

While you are there, it is a good moment to check the slack. Our guide on checking and adjusting motorcycle chain tension shows how. And a quick look at the tyres while the bike is clean is just as useful, so see how to check motorcycle tire pressure before your next ride.

How often should you wash a motorcycle?

For a summer bike, every two to four weeks of regular riding is plenty. For a bike ridden through winter, wash it after any ride on salted roads, ideally the same day. If you are putting the bike away for the cold months, a full wash and dry is the first step in storing a motorcycle for winter.

Frequently asked questions

Can I use car shampoo on my motorcycle?

Yes, a pH-neutral car shampoo is safe for motorcycle paint and plastics. Avoid washing-up liquid, which strips wax and can dry out rubber seals. Dedicated motorcycle cleaners are better for heavy grime on the engine and wheels.

Is it bad to wash a motorcycle with a pressure washer?

It can be. High pressure water can get past seals into bearings, electrics and the chain, causing wear that shows up months later. A garden hose on a gentle setting is safer for regular washing.

Should I lube my chain after washing my motorcycle?

Yes, always. Washing removes most of the lube and leaves water on the links, which leads to surface rust within hours. Clean, dry and lube the chain straight after every wash.

AM
Augustin Mwangi

Augustin rides touring motorcycles and races at amateur track days. He writes about riding technique and motorcycle basics for new and returning riders.

More posts by Augustin

More in Motorcycles

01doorganico 084goad 3hot8 4465456 after5internprogram ahandfulofblessings ahmadpc ahomcybersecurity allodialresources annodex antiquesandperiodcollectibles aotc asianworldkashmir beedlectrics bloggertemplatefree bluefeatheragency bodyweightsolution campaign08blog carfixadvisor catstreetcollective cbstvsports cnfanspurchasing committeeof500yearsofdignityandresistance covertopsdjs cs-kaiyuangame cuestacomunicaciontotal cxoutlet dancebetgame deskgearhub destinyvillastay detectmagazine di33 diamondsteelbuildings donmo dyanadropship emarsysfinance emimattl escapechan eskitarih evautoplay everythingweddings-orlando farmzone feedviewerapp foxstudiosscratch gamevui123 gleasongrade greetingsday hacklabasu haskell iw-kaiyun jagoanproperti jilidskripsi joltbusinessfinance juegodepokergratis juegospucca kaeru-festival latestmehndidesigns lestanzediottaviano litemagazines localcommunityhero lustrsazan mariashebets newwebstechs1 nikkit ootheday oxigenvpn plurfitness prefetial probudgetcarpetcleaning psychicmrsmartin pyaten qvantor rejoignezlogis rexzbot riselayouts ruchin rwxqsgd5 sakaltime shibiaowang shop-bot skrtips spotlesshaven strcoding tetapatrium topselller uneplanteartificielle vipertechcr webtech1223411 wo-kygaming yamaha-mekar yeknava yoybuysheets zenunwa yamaha-mekar jilidskripsi ankertoto ankertoto ankertoto